Skip to content
Carelabs·United Kingdom Power System Engineering·BS 7671·IET Wiring Regulations·HSR25·IEEE 1584·IEC 60909·ETAPCarelabs·United Kingdom Power System Engineering·BS 7671·IET Wiring Regulations·HSR25·IEEE 1584·IEC 60909·ETAPCarelabs·United Kingdom Power System Engineering·BS 7671·IET Wiring Regulations·HSR25·IEEE 1584·IEC 60909·ETAP
POWER SYSTEM STUDY · UNITED KINGDOM

Power System Study and Analysis for UK Sites

A power system study is not one study. It is load flow, short circuit, protection coordination and usually arc flash, each depending on the one before it. In the UK the chain starts with fault level data from your Distribution Network Operator, and every result downstream inherits whatever error is in that first number.

BS 7671 · IET Wiring Regulations · HSR25 · IEEE 1584 · IEC 60909

What We Deliver

What a UK Power System Study Covers

The components are standard. What makes a UK study usable is that the source data is documented and the studies are run in the right order.

01

Load flow and voltage profile

Establishes steady-state voltage at each bus, loading on transformers and cables, and where headroom exists. It is also the model everything else is built on, so errors here propagate into every later result.

02

Short circuit to IEC 60909

Fault levels calculated to IEC 60909, historically used in the UK alongside ENA Engineering Recommendation G74. This determines equipment adequacy and feeds directly into protection settings and arc flash energy.

03

Protection coordination

Grading upstream and downstream devices so the nearest device clears the fault. Under-grading trips the whole site for a local fault; over-grading extends clearing time, which raises incident energy at every downstream location.

04

Arc flash as the consequence

Incident energy follows from fault level and clearing time, so arc flash results are only as good as the coordination study behind them. Where an EAWR 1989 assessment is the objective, this is the chain that supports it.

Our Process

How We Run a UK Power System Study

01

Obtain DNO data

Request fault level and impedance at the point of common coupling in writing from the Distribution Network Operator for your licence area.

02

Verify the network on site

Confirm the single line diagram against the installation, record equipment ratings and conductor routes, and capture protection settings as found.

03

Load flow first

Build and validate the steady-state model, because every later study inherits it. Anomalies here are usually data errors worth resolving before proceeding.

04

Short circuit, then coordination

Calculate fault levels to IEC 60909, check equipment adequacy, then grade protection so clearing times are known rather than assumed.

05

Arc flash and reporting

Where in scope, incident energy from the coordinated clearing times, issued with the whole chain of inputs and assumptions in one report.

WHAT GOES WRONG

Where UK Power System Studies Fall Short

The usual failure is sequence. Studies commissioned separately, from different data, produce results that cannot be reconciled with each other when someone finally compares them.

FAQ

Frequently Asked Questions

What does a power system study actually include?

Load flow, short circuit, protection coordination and usually arc flash. They are sequential rather than independent: load flow establishes the model, short circuit gives fault levels, coordination sets clearing times, and incident energy follows from fault level and clearing time. Commissioning them separately is why results from different consultants often fail to reconcile.

Why does the DNO fault level matter so much?

Because it is the first input in the chain and everything downstream inherits it. Equipment adequacy, protection grading and arc flash incident energy all derive from it. An assumed figure carries its error into every result, which is why we request it in writing from the Distribution Network Operator for your licence area and record the source.

Can we do arc flash without the coordination study?

Not defensibly. Incident energy depends on how long the fault persists, and that is determined by protective device settings and their grading. Without a coordination study those clearing times are assumed, and an assumed clearing time produces a PPE category that cannot be justified if anyone examines the basis.

How often should the studies be revisited?

Whenever something changes the available fault current or the protection. A transformer replacement, a service upgrade, new protective devices or a DNO network reinforcement all invalidate the existing results. Sites frequently discover this after the fact, because a reinforcement upstream happens without any visible change on the site itself.

One Model, One Set of Inputs, Results That Reconcile

your study?